ua1zbe
cdd9d32fb5
Some checks failed
Build and deploy Docs site to GitHub Pages / github-pages (push) Has been cancelled
Run Unit Tests / test (push) Has been cancelled
PR Build Check / build (Heltec_v3_companion_radio_ble) (push) Has been cancelled
PR Build Check / build (Heltec_v3_repeater) (push) Has been cancelled
PR Build Check / build (Heltec_v3_room_server) (push) Has been cancelled
PR Build Check / build (LilyGo_Tlora_C6_repeater_) (push) Has been cancelled
PR Build Check / build (PicoW_repeater) (push) Has been cancelled
PR Build Check / build (RAK_4631_companion_radio_ble) (push) Has been cancelled
PR Build Check / build (RAK_4631_repeater) (push) Has been cancelled
PR Build Check / build (RAK_4631_room_server) (push) Has been cancelled
PR Build Check / build (Tbeam_SX1276_repeater) (push) Has been cancelled
PR Build Check / build (wio-e5-mini_repeater) (push) Has been cancelled
PR Build Check / build (wio_wm1110_repeater) (push) Has been cancelled
67 lines
2.1 KiB
C++
67 lines
2.1 KiB
C++
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
|
|
#include "RAK3401Board.h"
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Static configuration for power management
|
|
// Values set in variant.h defines
|
|
const PowerMgtConfig power_config = {
|
|
.lpcomp_ain_channel = PWRMGT_LPCOMP_AIN,
|
|
.lpcomp_refsel = PWRMGT_LPCOMP_REFSEL,
|
|
.voltage_bootlock = PWRMGT_VOLTAGE_BOOTLOCK
|
|
};
|
|
|
|
void RAK3401Board::initiateShutdown(uint8_t reason) {
|
|
// Disable SKY66122 FEM (CSD+CPS LOW = shutdown, <1 uA)
|
|
digitalWrite(SX126X_POWER_EN, LOW);
|
|
|
|
// Disable 3V3 switched peripherals and 5V boost
|
|
digitalWrite(PIN_3V3_EN, LOW);
|
|
|
|
if (reason == SHUTDOWN_REASON_LOW_VOLTAGE ||
|
|
reason == SHUTDOWN_REASON_BOOT_PROTECT) {
|
|
configureVoltageWake(power_config.lpcomp_ain_channel, power_config.lpcomp_refsel);
|
|
}
|
|
|
|
enterSystemOff(reason);
|
|
}
|
|
#endif
|
|
|
|
void RAK3401Board::begin() {
|
|
NRF52BoardDCDC::begin();
|
|
pinMode(PIN_VBAT_READ, INPUT);
|
|
#ifdef PIN_USER_BTN
|
|
pinMode(PIN_USER_BTN, INPUT_PULLUP);
|
|
#endif
|
|
|
|
#ifdef PIN_USER_BTN_ANA
|
|
pinMode(PIN_USER_BTN_ANA, INPUT_PULLUP);
|
|
#endif
|
|
|
|
#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
|
|
Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
|
|
#endif
|
|
|
|
Wire.begin();
|
|
|
|
// PIN_3V3_EN (WB_IO2, P0.34) controls the 3V3_S switched peripheral rail
|
|
// AND the 5V boost regulator (U5) on the RAK13302 that powers the SKY66122 PA.
|
|
// Must stay HIGH during radio operation — do not toggle for power saving.
|
|
pinMode(PIN_3V3_EN, OUTPUT);
|
|
digitalWrite(PIN_3V3_EN, HIGH);
|
|
|
|
// Enable SKY66122-11 FEM on the RAK13302 module.
|
|
// CSD and CPS are tied together on the RAK13302 PCB, routed to IO3 (P0.21).
|
|
// HIGH = FEM active (LNA for RX, PA path available for TX).
|
|
// TX/RX switching (CTX) is handled by SX1262 DIO2 via SetDIO2AsRfSwitchCtrl.
|
|
pinMode(SX126X_POWER_EN, OUTPUT);
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Boot voltage protection check (may not return if voltage too low)
|
|
// We need to call this after we configure SX126X_POWER_EN as output but before we pull high
|
|
checkBootVoltage(&power_config);
|
|
#endif
|
|
digitalWrite(SX126X_POWER_EN, HIGH);
|
|
delay(1); // SKY66122 turn-on settling time (tON = 3us typ)
|
|
}
|