ua1zbe
cdd9d32fb5
Some checks failed
Build and deploy Docs site to GitHub Pages / github-pages (push) Has been cancelled
Run Unit Tests / test (push) Has been cancelled
PR Build Check / build (Heltec_v3_companion_radio_ble) (push) Has been cancelled
PR Build Check / build (Heltec_v3_repeater) (push) Has been cancelled
PR Build Check / build (Heltec_v3_room_server) (push) Has been cancelled
PR Build Check / build (LilyGo_Tlora_C6_repeater_) (push) Has been cancelled
PR Build Check / build (PicoW_repeater) (push) Has been cancelled
PR Build Check / build (RAK_4631_companion_radio_ble) (push) Has been cancelled
PR Build Check / build (RAK_4631_repeater) (push) Has been cancelled
PR Build Check / build (RAK_4631_room_server) (push) Has been cancelled
PR Build Check / build (Tbeam_SX1276_repeater) (push) Has been cancelled
PR Build Check / build (wio-e5-mini_repeater) (push) Has been cancelled
PR Build Check / build (wio_wm1110_repeater) (push) Has been cancelled
57 lines
1.6 KiB
C++
57 lines
1.6 KiB
C++
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
|
|
#include "GAT562MeshTrackerProBoard.h"
|
|
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Static configuration for power management
|
|
// Values set in variant.h defines
|
|
const PowerMgtConfig power_config = {
|
|
.lpcomp_ain_channel = PWRMGT_LPCOMP_AIN,
|
|
.lpcomp_refsel = PWRMGT_LPCOMP_REFSEL,
|
|
.voltage_bootlock = PWRMGT_VOLTAGE_BOOTLOCK
|
|
};
|
|
|
|
|
|
void GAT562MeshTrackerProBoard::initiateShutdown(uint8_t reason) {
|
|
// Disable LoRa module power before shutdown
|
|
digitalWrite(SX126X_POWER_EN, LOW);
|
|
|
|
if (reason == SHUTDOWN_REASON_LOW_VOLTAGE ||
|
|
reason == SHUTDOWN_REASON_BOOT_PROTECT) {
|
|
configureVoltageWake(power_config.lpcomp_ain_channel, power_config.lpcomp_refsel);
|
|
}
|
|
|
|
enterSystemOff(reason);
|
|
}
|
|
#endif // NRF52_POWER_MANAGEMENT
|
|
|
|
|
|
void GAT562MeshTrackerProBoard::begin() {
|
|
NRF52BoardDCDC::begin();
|
|
pinMode(PIN_VBAT_READ, INPUT);
|
|
|
|
// Set all button pins to INPUT_PULLUP
|
|
pinMode(PIN_BUTTON1, INPUT_PULLUP);
|
|
pinMode(PIN_BUTTON2, INPUT_PULLUP);
|
|
pinMode(PIN_BUTTON3, INPUT_PULLUP);
|
|
pinMode(PIN_BUTTON4, INPUT_PULLUP);
|
|
pinMode(PIN_BUTTON5, INPUT_PULLUP);
|
|
pinMode(PIN_BUTTON6, INPUT_PULLUP);
|
|
|
|
#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
|
|
Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
|
|
#endif
|
|
|
|
Wire.begin();
|
|
|
|
pinMode(SX126X_POWER_EN, OUTPUT);
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Boot voltage protection check (may not return if voltage too low)
|
|
// We need to call this after we configure SX126X_POWER_EN as output but before we pull high
|
|
checkBootVoltage(&power_config);
|
|
#endif
|
|
digitalWrite(SX126X_POWER_EN, HIGH);
|
|
delay(10); // give sx1262 some time to power up
|
|
} |