Initial commit: Simple Sensor firmware for Heltec T114 with BME280

- MeshCore-based Simple Sensor firmware - Heltec T114 without display - BME280 sensor support (temp/humidity/pressure) - Radio: 868.856018 MHz, SF7, BW62.5 kHz, CR4/7 - 2-byte path hash - PlatformIO project
2026-06-01 16:19:09 +03:00
commit 42f55e12ae
725 changed files with 98374 additions and 0 deletions
--- a/variants/heltec_v4/HeltecV4Board.cpp
+++ b/variants/heltec_v4/HeltecV4Board.cpp
@@ -0,0 +1,85 @@
+#include "HeltecV4Board.h"
+
+void HeltecV4Board::begin() {
+    ESP32Board::begin();
+
+
+    pinMode(PIN_ADC_CTRL, OUTPUT);
+    digitalWrite(PIN_ADC_CTRL, LOW); // Initially inactive
+
+    loRaFEMControl.init();
+
+    periph_power.begin();
+    esp_reset_reason_t reason = esp_reset_reason();
+    if (reason == ESP_RST_DEEPSLEEP) {
+      long wakeup_source = esp_sleep_get_ext1_wakeup_status();
+      if (wakeup_source & (1 << P_LORA_DIO_1)) {  // received a LoRa packet (while in deep sleep)
+        startup_reason = BD_STARTUP_RX_PACKET;
+    }
+
+      rtc_gpio_hold_dis((gpio_num_t)P_LORA_NSS);
+      rtc_gpio_deinit((gpio_num_t)P_LORA_DIO_1);
+    }
+  }
+
+  void HeltecV4Board::onBeforeTransmit(void) {
+    digitalWrite(P_LORA_TX_LED, HIGH);   // turn TX LED on
+    loRaFEMControl.setTxModeEnable();
+  }
+
+  void HeltecV4Board::onAfterTransmit(void) {
+    digitalWrite(P_LORA_TX_LED, LOW);   // turn TX LED off
+    loRaFEMControl.setRxModeEnable();
+  }
+
+  void HeltecV4Board::enterDeepSleep(uint32_t secs, int pin_wake_btn) {
+    esp_sleep_pd_config(ESP_PD_DOMAIN_RTC_PERIPH, ESP_PD_OPTION_ON);
+
+    // Make sure the DIO1 and NSS GPIOs are hold on required levels during deep sleep
+    rtc_gpio_set_direction((gpio_num_t)P_LORA_DIO_1, RTC_GPIO_MODE_INPUT_ONLY);
+    rtc_gpio_pulldown_en((gpio_num_t)P_LORA_DIO_1);
+
+    rtc_gpio_hold_en((gpio_num_t)P_LORA_NSS);
+
+    loRaFEMControl.setRxModeEnableWhenMCUSleep();//It also needs to be enabled in receive mode
+
+    if (pin_wake_btn < 0) {
+      esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1), ESP_EXT1_WAKEUP_ANY_HIGH);  // wake up on: recv LoRa packet
+    } else {
+      esp_sleep_enable_ext1_wakeup( (1L << P_LORA_DIO_1) | (1L << pin_wake_btn), ESP_EXT1_WAKEUP_ANY_HIGH);  // wake up on: recv LoRa packet OR wake btn
+    }
+
+    if (secs > 0) {
+      esp_sleep_enable_timer_wakeup(secs * 1000000);
+    }
+
+    // Finally set ESP32 into sleep
+    esp_deep_sleep_start();   // CPU halts here and never returns!
+  }
+
+  void HeltecV4Board::powerOff()  {
+    enterDeepSleep(0);
+  }
+
+  uint16_t HeltecV4Board::getBattMilliVolts()  {
+    analogReadResolution(10);
+    digitalWrite(PIN_ADC_CTRL, HIGH);
+    delay(10);
+    uint32_t raw = 0;
+    for (int i = 0; i < 8; i++) {
+      raw += analogRead(PIN_VBAT_READ);
+    }
+    raw = raw / 8;
+
+    digitalWrite(PIN_ADC_CTRL, LOW);
+
+    return (5.42 * (3.3 / 1024.0) * raw) * 1000;
+  }
+
+  const char* HeltecV4Board::getManufacturerName() const {
+#ifdef HELTEC_LORA_V4_TFT
+    return loRaFEMControl.getFEMType() == KCT8103L_PA ? "Heltec V4.3 TFT" : "Heltec V4 TFT";
+#else
+    return loRaFEMControl.getFEMType() == KCT8103L_PA ? "Heltec V4.3 OLED" : "Heltec V4 OLED";
+#endif
+  }
--- a/variants/heltec_v4/HeltecV4Board.h
+++ b/variants/heltec_v4/HeltecV4Board.h
@@ -0,0 +1,23 @@
+#pragma once
+
+#include <Arduino.h>
+#include <helpers/RefCountedDigitalPin.h>
+#include <helpers/ESP32Board.h>
+#include <driver/rtc_io.h>
+#include "LoRaFEMControl.h"
+class HeltecV4Board : public ESP32Board {
+
+public:
+  RefCountedDigitalPin periph_power;
+  LoRaFEMControl loRaFEMControl;
+  HeltecV4Board() : periph_power(PIN_VEXT_EN,PIN_VEXT_EN_ACTIVE) { }
+
+  void begin();
+  void onBeforeTransmit(void) override;
+  void onAfterTransmit(void) override;
+  void enterDeepSleep(uint32_t secs, int pin_wake_btn = -1);
+  void powerOff() override;
+  uint16_t getBattMilliVolts() override;
+  const char* getManufacturerName() const override ;
+
+};
--- a/variants/heltec_v4/LoRaFEMControl.cpp
+++ b/variants/heltec_v4/LoRaFEMControl.cpp
@@ -0,0 +1,108 @@
+#include "LoRaFEMControl.h"
+#include <driver/rtc_io.h>
+#include <esp_sleep.h>
+#include <Arduino.h>
+
+void LoRaFEMControl::init(void)
+{
+    // Power on FEM LDO — set registers before releasing RTC hold for
+    // atomic transition (no glitch on deep sleep wake).
+    pinMode(P_LORA_PA_POWER, OUTPUT);
+    digitalWrite(P_LORA_PA_POWER, HIGH);
+    rtc_gpio_hold_dis((gpio_num_t)P_LORA_PA_POWER);
+
+    esp_reset_reason_t reason = esp_reset_reason();
+    if (reason != ESP_RST_DEEPSLEEP) {
+        delay(1);  // FEM startup time after cold power-on
+    }
+
+    // Auto-detect FEM type via shared GPIO2 default pull level.
+    // GC1109 CSD: internal pull-down → reads LOW
+    // KCT8103L CSD: internal pull-up → reads HIGH
+    rtc_gpio_hold_dis((gpio_num_t)P_LORA_KCT8103L_PA_CSD);
+    pinMode(P_LORA_KCT8103L_PA_CSD, INPUT);
+    delay(1);
+    if(digitalRead(P_LORA_KCT8103L_PA_CSD)==HIGH) {
+        // FEM is KCT8103L (V4.3)
+        fem_type= KCT8103L_PA;
+        pinMode(P_LORA_KCT8103L_PA_CSD, OUTPUT);
+        digitalWrite(P_LORA_KCT8103L_PA_CSD, HIGH);
+        rtc_gpio_hold_dis((gpio_num_t)P_LORA_KCT8103L_PA_CTX);
+        pinMode(P_LORA_KCT8103L_PA_CTX, OUTPUT);
+        digitalWrite(P_LORA_KCT8103L_PA_CTX, lna_enabled ? LOW : HIGH);
+        setLnaCanControl(true);
+    } else {
+        // FEM is GC1109 (V4.2)
+        fem_type= GC1109_PA;
+        pinMode(P_LORA_GC1109_PA_EN, OUTPUT);
+        digitalWrite(P_LORA_GC1109_PA_EN, HIGH);
+        pinMode(P_LORA_GC1109_PA_TX_EN, OUTPUT);
+        digitalWrite(P_LORA_GC1109_PA_TX_EN, LOW);
+    }
+}
+
+void LoRaFEMControl::setSleepModeEnable(void)
+{
+    if(fem_type==GC1109_PA) {
+    /*
+     * Do not switch the power on and off frequently.
+     * After turning off P_LORA_PA_EN, the power consumption has dropped to the uA level.
+     */
+    digitalWrite(P_LORA_GC1109_PA_EN, LOW);
+    digitalWrite(P_LORA_GC1109_PA_TX_EN, LOW);
+    } else if(fem_type==KCT8103L_PA) {
+        // shutdown the PA
+        digitalWrite(P_LORA_KCT8103L_PA_CSD, LOW);
+    }
+}
+
+void LoRaFEMControl::setTxModeEnable(void)
+{
+    if(fem_type==GC1109_PA) {
+        digitalWrite(P_LORA_GC1109_PA_EN, HIGH);   // CSD=1: Chip enabled
+        digitalWrite(P_LORA_GC1109_PA_TX_EN, HIGH); // CPS: 1=full PA, 0=bypass (for RX, CPS is don't care)
+    } else if(fem_type==KCT8103L_PA) {
+        digitalWrite(P_LORA_KCT8103L_PA_CSD, HIGH);
+        digitalWrite(P_LORA_KCT8103L_PA_CTX, HIGH);
+    }
+}
+
+void LoRaFEMControl::setRxModeEnable(void)
+{
+    if(fem_type==GC1109_PA) {
+        digitalWrite(P_LORA_GC1109_PA_EN, HIGH);  // CSD=1: Chip enabled
+        digitalWrite(P_LORA_GC1109_PA_TX_EN, LOW); 
+    } else if(fem_type==KCT8103L_PA) {
+        digitalWrite(P_LORA_KCT8103L_PA_CSD, HIGH);
+        if(lna_enabled) {
+            digitalWrite(P_LORA_KCT8103L_PA_CTX, LOW);   // LNA on
+        } else {
+            digitalWrite(P_LORA_KCT8103L_PA_CTX, HIGH);  // LNA bypass
+        }
+    }
+}
+
+void LoRaFEMControl::setRxModeEnableWhenMCUSleep(void)
+{
+    digitalWrite(P_LORA_PA_POWER, HIGH);
+    rtc_gpio_hold_en((gpio_num_t)P_LORA_PA_POWER);
+    if(fem_type==GC1109_PA) {
+        digitalWrite(P_LORA_GC1109_PA_EN, HIGH);
+        rtc_gpio_hold_en((gpio_num_t)P_LORA_GC1109_PA_EN);
+        gpio_pulldown_en((gpio_num_t)P_LORA_GC1109_PA_TX_EN);
+    } else if(fem_type==KCT8103L_PA) {
+        digitalWrite(P_LORA_KCT8103L_PA_CSD, HIGH);
+        rtc_gpio_hold_en((gpio_num_t)P_LORA_KCT8103L_PA_CSD);
+        if(lna_enabled) {
+            digitalWrite(P_LORA_KCT8103L_PA_CTX, LOW);   // LNA on
+        } else {
+            digitalWrite(P_LORA_KCT8103L_PA_CTX, HIGH);  // LNA bypass
+        }
+        rtc_gpio_hold_en((gpio_num_t)P_LORA_KCT8103L_PA_CTX);
+    }
+}
+
+void LoRaFEMControl::setLNAEnable(bool enabled)
+{
+    lna_enabled = enabled;
+}
--- a/variants/heltec_v4/LoRaFEMControl.h
+++ b/variants/heltec_v4/LoRaFEMControl.h
@@ -0,0 +1,29 @@
+#pragma once
+#include <stdint.h>
+
+typedef enum {
+    GC1109_PA,
+    KCT8103L_PA,
+    OTHER_FEM_TYPES
+} LoRaFEMType;
+
+class LoRaFEMControl
+{
+  public:
+    LoRaFEMControl(){ }
+    virtual ~LoRaFEMControl(){ }
+    void init(void);
+    void setSleepModeEnable(void);
+    void setTxModeEnable(void);
+    void setRxModeEnable(void);
+    void setRxModeEnableWhenMCUSleep(void);
+    void setLNAEnable(bool enabled);
+    bool isLnaCanControl(void) { return lna_can_control; }
+    void setLnaCanControl(bool can_control) { lna_can_control = can_control; }
+    LoRaFEMType getFEMType(void) const { return fem_type; }
+  private:
+    LoRaFEMType fem_type=OTHER_FEM_TYPES;
+    bool lna_enabled=true;
+    bool lna_can_control=false;
+};
+
--- a/variants/heltec_v4/pins_arduino.h
+++ b/variants/heltec_v4/pins_arduino.h
@@ -0,0 +1,67 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+static const uint8_t LED_BUILTIN = 35;
+#define BUILTIN_LED  LED_BUILTIN // backward compatibility
+#define LED_BUILTIN LED_BUILTIN  // allow testing #ifdef LED_BUILTIN
+
+static const uint8_t TX = 43;
+static const uint8_t RX = 44;
+
+static const uint8_t SDA = 3;
+static const uint8_t SCL = 4;
+
+static const uint8_t SS    = 8;
+static const uint8_t MOSI  = 10;
+static const uint8_t MISO  = 11;
+static const uint8_t SCK   = 9;
+
+static const uint8_t A0 = 1;
+static const uint8_t A1 = 2;
+static const uint8_t A2 = 3;
+static const uint8_t A3 = 4;
+static const uint8_t A4 = 5;
+static const uint8_t A5 = 6;
+static const uint8_t A6 = 7;
+static const uint8_t A7 = 8;
+static const uint8_t A8 = 9;
+static const uint8_t A9 = 10;
+static const uint8_t A10 = 11;
+static const uint8_t A11 = 12;
+static const uint8_t A12 = 13;
+static const uint8_t A13 = 14;
+static const uint8_t A14 = 15;
+static const uint8_t A15 = 16;
+static const uint8_t A16 = 17;
+static const uint8_t A17 = 18;
+static const uint8_t A18 = 19;
+static const uint8_t A19 = 20;
+
+static const uint8_t T1 = 1;
+static const uint8_t T2 = 2;
+static const uint8_t T3 = 3;
+static const uint8_t T4 = 4;
+static const uint8_t T5 = 5;
+static const uint8_t T6 = 6;
+static const uint8_t T7 = 7;
+static const uint8_t T8 = 8;
+static const uint8_t T9 = 9;
+static const uint8_t T10 = 10;
+static const uint8_t T11 = 11;
+static const uint8_t T12 = 12;
+static const uint8_t T13 = 13;
+static const uint8_t T14 = 14;
+
+static const uint8_t Vext = 36;
+static const uint8_t LED  = 35;
+static const uint8_t RST_OLED = 21;
+static const uint8_t SCL_OLED = 18;
+static const uint8_t SDA_OLED = 17;
+
+static const uint8_t RST_LoRa = 12;
+static const uint8_t BUSY_LoRa = 13;
+static const uint8_t DIO0 = 14;
+
+#endif /* Pins_Arduino_h */
--- a/variants/heltec_v4/platformio.ini
+++ b/variants/heltec_v4/platformio.ini
@@ -0,0 +1,409 @@
+[Heltec_lora32_v4]
+extends = esp32_base
+board = heltec_v4
+build_flags =
+  ${esp32_base.build_flags}
+  ${sensor_base.build_flags}
+  -I variants/heltec_v4
+  -D HELTEC_LORA_V4
+  -D USE_SX1262
+  -D ESP32_CPU_FREQ=80
+  -D RADIO_CLASS=CustomSX1262
+  -D WRAPPER_CLASS=CustomSX1262Wrapper
+  -D P_LORA_TX_LED=35
+  -D P_LORA_DIO_1=14
+  -D P_LORA_NSS=8
+  -D P_LORA_RESET=12
+  -D P_LORA_BUSY=13
+  -D P_LORA_SCLK=9
+  -D P_LORA_MISO=11
+  -D P_LORA_MOSI=10
+  -D P_LORA_PA_POWER=7  ; // VFEM_Ctrl -LDO power enable
+  -D P_LORA_GC1109_PA_EN=2    ; // CSD - GC1109 chip enable (HIGH=on)
+  -D P_LORA_GC1109_PA_TX_EN=46 ;// CPS - GC1109 PA mode (HIGH=full PA, LOW=bypass)
+  -D P_LORA_KCT8103L_PA_CSD=2
+  -D P_LORA_KCT8103L_PA_CTX=5
+  -D PIN_USER_BTN=0
+  -D PIN_VEXT_EN=36
+  -D PIN_VEXT_EN_ACTIVE=HIGH
+  -D LORA_TX_POWER=10 ;If it is configured as 10 here, the final output will be 22 dbm.
+  -D MAX_LORA_TX_POWER=22 ; Max SX1262 output
+  -D SX126X_REGISTER_PATCH=1       ; Patch register 0x8B5 for improved RX
+  -D SX126X_DIO2_AS_RF_SWITCH=true ; GC1109 CTX is controlled by SX1262 DIO2
+  -D SX126X_DIO3_TCXO_VOLTAGE=1.8
+  -D SX126X_CURRENT_LIMIT=140
+  -D SX126X_RX_BOOSTED_GAIN=1      ; In some cases, commenting this out will improve RX
+  -D PIN_GPS_RX=38
+  -D PIN_GPS_TX=39
+  -D PIN_GPS_RESET=42
+  -D PIN_GPS_RESET_ACTIVE=LOW
+  -D PIN_GPS_EN=34
+  -D PIN_GPS_EN_ACTIVE=LOW
+  -D ENV_INCLUDE_GPS=1
+  -D PIN_ADC_CTRL=37
+  -D PIN_VBAT_READ=1
+build_src_filter = ${esp32_base.build_src_filter}
+  +<../variants/heltec_v4>
+  +<helpers/sensors>
+lib_deps =
+  ${esp32_base.lib_deps}
+  ${sensor_base.lib_deps}
+
+[heltec_v4_oled]
+extends = Heltec_lora32_v4
+build_flags =
+  ${Heltec_lora32_v4.build_flags}
+  -D HELTEC_LORA_V4_OLED
+  -D PIN_BOARD_SDA=17
+  -D PIN_BOARD_SCL=18
+  -D PIN_OLED_RESET=21
+build_src_filter= ${Heltec_lora32_v4.build_src_filter}
+lib_deps = ${Heltec_lora32_v4.lib_deps}
+
+[heltec_v4_tft]
+extends = Heltec_lora32_v4
+build_flags =
+  ${Heltec_lora32_v4.build_flags}
+  -D HELTEC_LORA_V4_TFT
+  -D PIN_BOARD_SDA=4
+  -D PIN_BOARD_SCL=3
+  -D DISPLAY_SCALE_X=2.5
+  -D DISPLAY_SCALE_Y=3.75
+  -D PIN_TFT_RST=18
+  -D PIN_TFT_VDD_CTL=-1
+  -D PIN_TFT_LEDA_CTL=21
+  -D PIN_TFT_LEDA_CTL_ACTIVE=HIGH
+  -D PIN_TFT_CS=15
+  -D PIN_TFT_DC=16
+  -D PIN_TFT_SCL=17
+  -D PIN_TFT_SDA=33
+build_src_filter= ${Heltec_lora32_v4.build_src_filter}
+lib_deps = 
+  ${Heltec_lora32_v4.lib_deps}
+  adafruit/Adafruit ST7735 and ST7789 Library @ ^1.11.0
+
+[env:heltec_v4_repeater]
+extends = heltec_v4_oled
+build_flags =
+  ${heltec_v4_oled.build_flags}
+  -D DISPLAY_CLASS=SSD1306Display
+  -D ADVERT_NAME='"Heltec Repeater"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D MAX_NEIGHBOURS=50
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_oled.build_src_filter}
+  +<helpers/ui/SSD1306Display.cpp>
+  +<../examples/simple_repeater>
+lib_deps =
+  ${heltec_v4_oled.lib_deps}
+  ${esp32_ota.lib_deps}
+  bakercp/CRC32 @ ^2.0.0
+
+[env:heltec_v4_repeater_bridge_espnow]
+extends = heltec_v4_oled
+build_flags =
+  ${heltec_v4_oled.build_flags}
+  -D DISPLAY_CLASS=SSD1306Display
+  -D ADVERT_NAME='"ESPNow Bridge"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D MAX_NEIGHBOURS=50
+  -D WITH_ESPNOW_BRIDGE=1
+;  -D BRIDGE_DEBUG=1
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_oled.build_src_filter}
+  +<helpers/bridges/ESPNowBridge.cpp>
+  +<helpers/ui/SSD1306Display.cpp>
+  +<../examples/simple_repeater>
+lib_deps =
+  ${heltec_v4_oled.lib_deps}
+  ${esp32_ota.lib_deps}
+
+[env:heltec_v4_room_server]
+extends = heltec_v4_oled
+build_flags =
+  ${heltec_v4_oled.build_flags}
+  -D DISPLAY_CLASS=SSD1306Display
+  -D ADVERT_NAME='"Heltec Room"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D ROOM_PASSWORD='"hello"'
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_oled.build_src_filter}
+  +<helpers/ui/SSD1306Display.cpp>
+  +<../examples/simple_room_server>
+lib_deps =
+  ${heltec_v4_oled.lib_deps}
+  ${esp32_ota.lib_deps}
+
+[env:heltec_v4_terminal_chat]
+extends = heltec_v4_oled
+build_flags =
+  ${heltec_v4_oled.build_flags}
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=1
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_oled.build_src_filter}
+  +<../examples/simple_secure_chat/main.cpp>
+lib_deps =
+  ${heltec_v4_oled.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+
+[env:heltec_v4_companion_radio_usb]
+extends = heltec_v4_oled
+build_flags =
+  ${heltec_v4_oled.build_flags}
+  -I examples/companion_radio/ui-new
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=40
+  -D DISPLAY_CLASS=SSD1306Display
+; NOTE: DO NOT ENABLE -->  -D MESH_PACKET_LOGGING=1
+; NOTE: DO NOT ENABLE -->  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_oled.build_src_filter}
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<../examples/companion_radio/*.cpp>
+  +<../examples/companion_radio/ui-new/*.cpp>
+lib_deps =
+  ${heltec_v4_oled.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+
+[env:heltec_v4_companion_radio_ble]
+extends = heltec_v4_oled
+build_flags =
+  ${heltec_v4_oled.build_flags}
+  -I examples/companion_radio/ui-new
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=40
+  -D DISPLAY_CLASS=SSD1306Display
+  -D BLE_PIN_CODE=123456   ; dynamic, random PIN
+  -D AUTO_SHUTDOWN_MILLIVOLTS=3400
+  -D BLE_DEBUG_LOGGING=1
+  -D OFFLINE_QUEUE_SIZE=256
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_oled.build_src_filter}
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<helpers/esp32/*.cpp>
+  +<../examples/companion_radio/*.cpp>
+  +<../examples/companion_radio/ui-new/*.cpp>
+lib_deps =
+  ${heltec_v4_oled.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+
+[env:heltec_v4_companion_radio_wifi]
+extends = heltec_v4_oled
+build_flags =
+  ${heltec_v4_oled.build_flags}
+  -I examples/companion_radio/ui-new
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=40
+  -D OFFLINE_QUEUE_SIZE=256
+  -D DISPLAY_CLASS=SSD1306Display
+  -D WIFI_DEBUG_LOGGING=1
+  -D WIFI_SSID='"myssid"'
+  -D WIFI_PWD='"mypwd"'
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_oled.build_src_filter}
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<helpers/esp32/*.cpp>
+  +<../examples/companion_radio/*.cpp>
+  +<../examples/companion_radio/ui-new/*.cpp>
+lib_deps =
+  ${heltec_v4_oled.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+
+[env:heltec_v4_sensor]
+extends = heltec_v4_oled
+build_flags =
+  ${heltec_v4_oled.build_flags}
+  -D ADVERT_NAME='"Heltec v4 Sensor"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D ENV_PIN_SDA=3
+  -D ENV_PIN_SCL=4
+  -D DISPLAY_CLASS=SSD1306Display
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_oled.build_src_filter}
+  +<helpers/ui/SSD1306Display.cpp>
+  +<../examples/simple_sensor>
+lib_deps =
+  ${heltec_v4_oled.lib_deps}
+  ${esp32_ota.lib_deps}
+
+
+[env:heltec_v4_tft_repeater]
+extends = heltec_v4_tft
+build_flags =
+  ${heltec_v4_tft.build_flags}
+  -D DISPLAY_CLASS=ST7789LCDDisplay
+  -D ADVERT_NAME='"Heltec Repeater"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D MAX_NEIGHBOURS=50
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_tft.build_src_filter}
+  +<helpers/ui/ST7789LCDDisplay.cpp>
+  +<../examples/simple_repeater>
+lib_deps =
+  ${heltec_v4_tft.lib_deps}
+  ${esp32_ota.lib_deps}
+  bakercp/CRC32 @ ^2.0.0
+
+
+[env:heltec_v4_tft_repeater_bridge_espnow]
+extends = heltec_v4_tft
+build_flags =
+  ${heltec_v4_tft.build_flags}
+  -D DISPLAY_CLASS=ST7789LCDDisplay
+  -D ADVERT_NAME='"ESPNow Bridge"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D MAX_NEIGHBOURS=50
+  -D WITH_ESPNOW_BRIDGE=1
+;  -D BRIDGE_DEBUG=1
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_tft.build_src_filter}
+  +<helpers/bridges/ESPNowBridge.cpp>
+  +<helpers/ui/ST7789LCDDisplay.cpp>
+  +<../examples/simple_repeater>
+lib_deps =
+  ${heltec_v4_tft.lib_deps}
+  ${esp32_ota.lib_deps}
+
+[env:heltec_v4_tft_room_server]
+extends = heltec_v4_tft
+build_flags =
+  ${heltec_v4_tft.build_flags}
+  -D DISPLAY_CLASS=ST7789LCDDisplay
+  -D ADVERT_NAME='"Heltec Room"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D ROOM_PASSWORD='"hello"'
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_tft.build_src_filter}
+  +<helpers/ui/ST7789LCDDisplay.cpp>
+  +<../examples/simple_room_server>
+lib_deps =
+  ${heltec_v4_tft.lib_deps}
+  ${esp32_ota.lib_deps}
+
+[env:heltec_v4_tft_terminal_chat]
+extends = heltec_v4_tft
+build_flags =
+  ${heltec_v4_tft.build_flags}
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=1
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_tft.build_src_filter}
+  +<../examples/simple_secure_chat/main.cpp>
+lib_deps =
+  ${heltec_v4_tft.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+
+[env:heltec_v4_tft_companion_radio_usb]
+extends = heltec_v4_tft
+build_flags =
+  ${heltec_v4_tft.build_flags}
+  -I examples/companion_radio/ui-new
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=40
+  -D DISPLAY_CLASS=ST7789LCDDisplay
+; NOTE: DO NOT ENABLE -->  -D MESH_PACKET_LOGGING=1
+; NOTE: DO NOT ENABLE -->  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_tft.build_src_filter}
+  +<helpers/ui/ST7789LCDDisplay.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<../examples/companion_radio/*.cpp>
+  +<../examples/companion_radio/ui-new/*.cpp>
+lib_deps =
+  ${heltec_v4_tft.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+
+[env:heltec_v4_tft_companion_radio_ble]
+extends = heltec_v4_tft
+build_flags =
+  ${heltec_v4_tft.build_flags}
+  -I examples/companion_radio/ui-new
+  -D DISPLAY_CLASS=ST7789LCDDisplay
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=40
+  -D BLE_PIN_CODE=123456   ; dynamic, random PIN
+  -D AUTO_SHUTDOWN_MILLIVOLTS=3400
+  -D BLE_DEBUG_LOGGING=1
+  -D OFFLINE_QUEUE_SIZE=256
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_tft.build_src_filter}
+  +<helpers/ui/ST7789LCDDisplay.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<helpers/esp32/*.cpp>
+  +<../examples/companion_radio/*.cpp>
+  +<../examples/companion_radio/ui-new/*.cpp>
+lib_deps =
+  ${heltec_v4_tft.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+
+[env:heltec_v4_tft_companion_radio_wifi]
+extends = heltec_v4_tft
+build_flags =
+  ${heltec_v4_tft.build_flags}
+  -I examples/companion_radio/ui-new
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=40
+  -D OFFLINE_QUEUE_SIZE=256
+  -D DISPLAY_CLASS=ST7789LCDDisplay
+  -D WIFI_DEBUG_LOGGING=1
+  -D WIFI_SSID='"myssid"'
+  -D WIFI_PWD='"mypwd"'
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_tft.build_src_filter}
+  +<helpers/ui/ST7789LCDDisplay.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<helpers/esp32/*.cpp>
+  +<../examples/companion_radio/*.cpp>
+  +<../examples/companion_radio/ui-new/*.cpp>
+lib_deps =
+  ${heltec_v4_tft.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+
+[env:heltec_v4_tft_sensor]
+extends = heltec_v4_tft
+build_flags =
+  ${heltec_v4_tft.build_flags}
+  -D ADVERT_NAME='"Heltec v4 Sensor"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D ENV_PIN_SDA=3
+  -D ENV_PIN_SCL=4
+  -D DISPLAY_CLASS=ST7789LCDDisplay
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${heltec_v4_tft.build_src_filter}
+  +<helpers/ui/ST7789LCDDisplay.cpp>
+  +<../examples/simple_sensor>
+lib_deps =
+  ${heltec_v4_tft.lib_deps}
+  ${esp32_ota.lib_deps}
--- a/variants/heltec_v4/target.cpp
+++ b/variants/heltec_v4/target.cpp
@@ -0,0 +1,61 @@
+#include <Arduino.h>
+#include "target.h"
+
+HeltecV4Board board;
+
+#if defined(P_LORA_SCLK)
+  static SPIClass spi;
+  RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, spi);
+#else
+  RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY);
+#endif
+
+WRAPPER_CLASS radio_driver(radio, board);
+
+ESP32RTCClock fallback_clock;
+AutoDiscoverRTCClock rtc_clock(fallback_clock);
+
+#if ENV_INCLUDE_GPS
+  #include <helpers/sensors/MicroNMEALocationProvider.h>
+  MicroNMEALocationProvider nmea = MicroNMEALocationProvider(Serial1, &rtc_clock);
+  EnvironmentSensorManager sensors = EnvironmentSensorManager(nmea);
+#else
+  EnvironmentSensorManager sensors;
+#endif
+
+#ifdef DISPLAY_CLASS
+  DISPLAY_CLASS display(NULL);
+  MomentaryButton user_btn(PIN_USER_BTN, 1000, true);
+#endif
+
+bool radio_init() {
+  fallback_clock.begin();
+  rtc_clock.begin(Wire);
+  
+#if defined(P_LORA_SCLK)
+  return radio.std_init(&spi);
+#else
+  return radio.std_init();
+#endif
+}
+
+uint32_t radio_get_rng_seed() {
+  return radio.random(0x7FFFFFFF);
+}
+
+void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr) {
+  radio.setFrequency(freq);
+  radio.setSpreadingFactor(sf);
+  radio.setBandwidth(bw);
+  radio.setCodingRate(cr);
+}
+
+void radio_set_tx_power(int8_t dbm) {
+  radio.setOutputPower(dbm);
+}
+
+mesh::LocalIdentity radio_new_identity() {
+  RadioNoiseListener rng(radio);
+  return mesh::LocalIdentity(&rng);  // create new random identity
+}
+
--- a/variants/heltec_v4/target.h
+++ b/variants/heltec_v4/target.h
@@ -0,0 +1,35 @@
+#pragma once
+
+#define RADIOLIB_STATIC_ONLY 1
+#include <RadioLib.h>
+#include <helpers/radiolib/RadioLibWrappers.h>
+#include <HeltecV4Board.h>
+#include <helpers/radiolib/CustomSX1262Wrapper.h>
+#include <helpers/AutoDiscoverRTCClock.h>
+#include <helpers/SensorManager.h>
+#include <helpers/sensors/EnvironmentSensorManager.h>
+#ifdef DISPLAY_CLASS
+#ifdef HELTEC_LORA_V4_OLED
+    #include <helpers/ui/SSD1306Display.h>
+#elif defined(HELTEC_LORA_V4_TFT)
+    #include <helpers/ui/ST7789LCDDisplay.h>
+#endif
+  #include <helpers/ui/MomentaryButton.h>
+#endif
+
+extern HeltecV4Board board;
+extern WRAPPER_CLASS radio_driver;
+extern AutoDiscoverRTCClock rtc_clock;
+extern EnvironmentSensorManager sensors;
+
+#ifdef DISPLAY_CLASS
+  extern DISPLAY_CLASS display;
+  extern MomentaryButton user_btn;
+#endif
+
+bool radio_init();
+uint32_t radio_get_rng_seed();
+void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr);
+void radio_set_tx_power(int8_t dbm);
+mesh::LocalIdentity radio_new_identity();
+