Initial commit: Simple Sensor firmware for Heltec T114 with BME280

- MeshCore-based Simple Sensor firmware
- Heltec T114 without display
- BME280 sensor support (temp/humidity/pressure)
- Radio: 868.856018 MHz, SF7, BW62.5 kHz, CR4/7
- 2-byte path hash
- PlatformIO project

variants/promicro/PromicroBoard.cpp

@@ -0,0 +1,25 @@
+#include <Arduino.h>
+#include <Wire.h>
+
+#include "PromicroBoard.h"
+
+void PromicroBoard::begin() {    
+    NRF52Board::begin();
+    btn_prev_state = HIGH;
+  
+    pinMode(PIN_VBAT_READ, INPUT);
+
+    #ifdef BUTTON_PIN
+      pinMode(BUTTON_PIN, INPUT_PULLUP);
+    #endif
+
+    #if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
+      Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
+    #endif
+    
+    Wire.begin();
+
+    pinMode(SX126X_POWER_EN, OUTPUT);
+    digitalWrite(SX126X_POWER_EN, HIGH);
+    delay(10);   // give sx1262 some time to power up
+}

variants/promicro/PromicroBoard.h

@@ -0,0 +1,79 @@
+#pragma once
+
+#include <MeshCore.h>
+#include <Arduino.h>
+#include <helpers/NRF52Board.h>
+
+#define P_LORA_NSS 13 //P1.13 45
+#define P_LORA_DIO_1 11 //P0.10 10
+#define P_LORA_RESET 10 //P0.09 9
+#define P_LORA_BUSY  16 //P0.29 29
+#define P_LORA_MISO  15 //P0.02 2
+#define P_LORA_SCLK  12 //P1.11 43
+#define P_LORA_MOSI  14 //P1.15 47
+#define SX126X_POWER_EN 21 //P0.13 13
+#define SX126X_RXEN 2 //P0.17
+#define SX126X_TXEN RADIOLIB_NC
+#define SX126X_DIO2_AS_RF_SWITCH  true
+#define SX126X_DIO3_TCXO_VOLTAGE (1.8f)
+
+#define  PIN_VBAT_READ 17
+#define  ADC_MULTIPLIER   (1.815f) // dependent on voltage divider resistors. TODO: more accurate battery tracking
+
+class PromicroBoard : public NRF52BoardDCDC {
+protected:
+  uint8_t btn_prev_state;
+  float adc_mult = ADC_MULTIPLIER;
+
+public:
+  PromicroBoard() : NRF52Board("ProMicro_OTA") {}
+  void begin();
+
+  #define BATTERY_SAMPLES 8
+
+  uint16_t getBattMilliVolts() override {
+    analogReadResolution(12);
+
+    uint32_t raw = 0;
+    for (int i = 0; i < BATTERY_SAMPLES; i++) {
+      raw += analogRead(PIN_VBAT_READ);
+    }
+    raw = raw / BATTERY_SAMPLES;
+    return (adc_mult * raw);
+  }
+
+  bool setAdcMultiplier(float multiplier) override {
+    if (multiplier == 0.0f) {
+      adc_mult = ADC_MULTIPLIER;}
+    else {
+      adc_mult = multiplier;
+    }
+    return true;
+  }
+  float getAdcMultiplier() const override {
+    if (adc_mult == 0.0f) {
+      return ADC_MULTIPLIER;
+    } else {
+      return adc_mult;
+    }
+  }
+
+  const char* getManufacturerName() const override {
+    return "ProMicro DIY";
+  }
+
+  int buttonStateChanged() {
+    #ifdef BUTTON_PIN
+      uint8_t v = digitalRead(BUTTON_PIN);
+      if (v != btn_prev_state) {
+        btn_prev_state = v;
+        return (v == LOW) ? 1 : -1;
+      }
+    #endif
+      return 0;
+  }
+
+  void powerOff() override {
+    sd_power_system_off();
+  }
+};

variants/promicro/platformio.ini

@@ -0,0 +1,173 @@
+[Promicro]
+extends = nrf52_base
+board = promicro_nrf52840
+build_flags = ${nrf52_base.build_flags}
+  -I variants/promicro
+  -D PROMICRO
+  -D USE_SX1262
+  -D RADIO_CLASS=CustomSX1262
+  -D WRAPPER_CLASS=CustomSX1262Wrapper
+  -D LORA_TX_POWER=22
+  -D SX126X_CURRENT_LIMIT=140
+  -D SX126X_RX_BOOSTED_GAIN=1
+  -D PIN_BOARD_SCL=7
+  -D PIN_BOARD_SDA=8
+  -D PIN_OLED_RESET=-1
+  -D PIN_USER_BTN=6
+  -D PIN_GPS_RX=3
+  -D PIN_GPS_TX=4
+  -D PIN_GPS_EN=5
+  -D ENV_INCLUDE_GPS=1
+  -D ENV_INCLUDE_AHTX0=1
+  -D ENV_INCLUDE_BME280=1
+  -D ENV_INCLUDE_BMP280=1
+  -D ENV_INCLUDE_INA3221=1
+  -D ENV_INCLUDE_INA219=1
+build_src_filter = ${nrf52_base.build_src_filter}
+  +<helpers/sensors>
+  +<../variants/promicro>
+lib_deps= ${nrf52_base.lib_deps}
+	adafruit/Adafruit SSD1306 @ ^2.5.13
+  adafruit/Adafruit INA3221 Library @ ^1.0.1
+  adafruit/Adafruit INA219 @ ^1.2.3
+  adafruit/Adafruit AHTX0 @ ^2.0.5
+  adafruit/Adafruit BME280 Library @ ^2.3.0
+  adafruit/Adafruit BMP280 Library@^2.6.8
+  stevemarple/MicroNMEA @ ^2.0.6
+
+[env:ProMicro_repeater]
+extends = Promicro
+build_src_filter = ${Promicro.build_src_filter}
+  +<../examples/simple_repeater>
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+build_flags =
+  ${Promicro.build_flags}
+  -D ADVERT_NAME='"ProMicro Repeater"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D MAX_NEIGHBOURS=50
+  -D DISPLAY_CLASS=SSD1306Display
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+lib_deps = ${Promicro.lib_deps}
+  adafruit/RTClib @ ^2.1.3
+
+[env:ProMicro_repeater_bridge_rs232_serial1]
+extends = Promicro
+build_src_filter = ${Promicro.build_src_filter}
+  +<../examples/simple_repeater>
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<helpers/bridges/RS232Bridge.cpp>
+build_flags =
+  ${Promicro.build_flags}
+  -D ADVERT_NAME='"RS232 Bridge"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D MAX_NEIGHBOURS=50
+  -D DISPLAY_CLASS=SSD1306Display
+  -D WITH_RS232_BRIDGE=Serial1
+  -D WITH_RS232_BRIDGE_RX=PIN_SERIAL1_RX
+  -D WITH_RS232_BRIDGE_TX=PIN_SERIAL1_TX
+  -UENV_INCLUDE_GPS
+;  -D BRIDGE_DEBUG=1
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+lib_deps = ${Promicro.lib_deps}
+  adafruit/RTClib @ ^2.1.3
+
+[env:ProMicro_room_server]
+extends = Promicro
+build_src_filter = ${Promicro.build_src_filter}
+  +<../examples/simple_room_server>
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+build_flags = ${Promicro.build_flags}
+  -D ADVERT_NAME='"ProMicro Room"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D ROOM_PASSWORD='"hello"'
+  -D DISPLAY_CLASS=SSD1306Display
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+lib_deps = ${Promicro.lib_deps}
+  adafruit/RTClib @ ^2.1.3
+
+[env:ProMicro_terminal_chat]
+extends = Promicro
+build_flags = ${Promicro.build_flags}
+  -D MAX_CONTACTS=100
+  -D MAX_GROUP_CHANNELS=1
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${Promicro.build_src_filter}
+  +<../examples/simple_secure_chat/main.cpp>
+lib_deps = ${Promicro.lib_deps}
+  densaugeo/base64 @ ~1.4.0
+  adafruit/RTClib @ ^2.1.3
+
+[env:ProMicro_companion_radio_usb]
+extends = Promicro
+board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld
+board_upload.maximum_size = 712704
+build_flags = ${Promicro.build_flags}
+  -I examples/companion_radio/ui-new
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=40
+  -D DISPLAY_CLASS=SSD1306Display
+; NOTE: DO NOT ENABLE -->  -D MESH_PACKET_LOGGING=1
+; NOTE: DO NOT ENABLE -->  -D MESH_DEBUG=1
+build_src_filter = ${Promicro.build_src_filter}
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<../examples/companion_radio/*.cpp>
+  +<../examples/companion_radio/ui-new/*.cpp>
+lib_deps = ${Promicro.lib_deps}
+  adafruit/RTClib @ ^2.1.3
+  densaugeo/base64 @ ~1.4.0
+
+[env:ProMicro_companion_radio_ble]
+extends = Promicro
+board_build.ldscript = boards/nrf52840_s140_v6_extrafs.ld
+board_upload.maximum_size = 712704
+build_flags = ${Promicro.build_flags}
+  -I examples/companion_radio/ui-new
+  -D MAX_CONTACTS=350
+  -D MAX_GROUP_CHANNELS=40
+  -D BLE_PIN_CODE=123456
+  -D BLE_DEBUG_LOGGING=1
+  -D OFFLINE_QUEUE_SIZE=256
+  -D DISPLAY_CLASS=SSD1306Display
+;  -D MESH_PACKET_LOGGING=1
+  -D MESH_DEBUG=1
+build_src_filter = ${Promicro.build_src_filter}
+  +<helpers/nrf52/SerialBLEInterface.cpp>
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<../examples/companion_radio/*.cpp>
+  +<../examples/companion_radio/ui-new/*.cpp>
+lib_deps = ${Promicro.lib_deps}
+  adafruit/RTClib @ ^2.1.3
+  densaugeo/base64 @ ~1.4.0
+
+[env:ProMicro_sensor]
+extends = Promicro
+build_flags =
+  ${Promicro.build_flags}
+  -D ADVERT_NAME='"ProMicro Sensor"'
+  -D ADVERT_LAT=0.0
+  -D ADVERT_LON=0.0
+  -D ADMIN_PASSWORD='"password"'
+  -D DISPLAY_CLASS=SSD1306Display
+;  -D MESH_PACKET_LOGGING=1
+;  -D MESH_DEBUG=1
+build_src_filter = ${Promicro.build_src_filter}
+  +<helpers/ui/SSD1306Display.cpp>
+  +<helpers/ui/MomentaryButton.cpp>
+  +<../examples/simple_sensor>
+lib_deps =
+  ${Promicro.lib_deps}

variants/promicro/target.cpp

@@ -0,0 +1,52 @@
+#include <Arduino.h>
+#include "target.h"
+#include <helpers/ArduinoHelpers.h>
+
+PromicroBoard board;
+
+RADIO_CLASS radio = new Module(P_LORA_NSS, P_LORA_DIO_1, P_LORA_RESET, P_LORA_BUSY, SPI);
+
+WRAPPER_CLASS radio_driver(radio, board);
+
+VolatileRTCClock fallback_clock;
+AutoDiscoverRTCClock rtc_clock(fallback_clock);
+#if ENV_INCLUDE_GPS
+  #include <helpers/sensors/MicroNMEALocationProvider.h>
+  MicroNMEALocationProvider nmea = MicroNMEALocationProvider(Serial1, &rtc_clock);
+  EnvironmentSensorManager sensors = EnvironmentSensorManager(nmea);
+#else
+  EnvironmentSensorManager sensors;
+#endif
+
+#ifdef DISPLAY_CLASS
+  DISPLAY_CLASS display;
+  MomentaryButton user_btn(PIN_USER_BTN, 1000, true, true);
+#endif
+
+bool radio_init() {
+  rtc_clock.begin(Wire);
+  
+  return radio.std_init(&SPI);
+}
+
+uint32_t radio_get_rng_seed() {
+  return radio.random(0x7FFFFFFF);
+}
+
+void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr) {
+  radio.setFrequency(freq);
+  radio.setSpreadingFactor(sf);
+  radio.setBandwidth(bw);
+  radio.setCodingRate(cr);
+}
+
+void radio_set_tx_power(int8_t dbm) {
+  radio.setOutputPower(dbm);
+}
+
+mesh::LocalIdentity radio_new_identity() {
+  RadioNoiseListener rng(radio);
+  return mesh::LocalIdentity(&rng);  // create new random identity
+}
+
+

variants/promicro/target.h

@@ -0,0 +1,31 @@
+#pragma once
+
+#define RADIOLIB_STATIC_ONLY 1
+#include <RadioLib.h>
+#include <helpers/radiolib/RadioLibWrappers.h>
+#include <PromicroBoard.h>
+#include <helpers/radiolib/CustomSX1262Wrapper.h>
+#include <helpers/AutoDiscoverRTCClock.h>
+#ifdef DISPLAY_CLASS
+  #include <helpers/ui/SSD1306Display.h>
+  #include <helpers/ui/MomentaryButton.h>
+#endif
+
+#include <helpers/sensors/EnvironmentSensorManager.h>
+
+extern PromicroBoard board;
+extern WRAPPER_CLASS radio_driver;
+extern AutoDiscoverRTCClock rtc_clock;
+extern EnvironmentSensorManager sensors;
+
+#ifdef DISPLAY_CLASS
+  extern DISPLAY_CLASS display;
+  extern MomentaryButton user_btn;
+#endif
+
+bool radio_init();
+uint32_t radio_get_rng_seed();
+void radio_set_params(float freq, float bw, uint8_t sf, uint8_t cr);
+void radio_set_tx_power(int8_t dbm);
+mesh::LocalIdentity radio_new_identity();
+

variants/promicro/variant.cpp

@@ -0,0 +1,15 @@
+#include "variant.h"
+#include "wiring_constants.h"
+#include "wiring_digital.h"
+
+const uint32_t g_ADigitalPinMap[] = {
+  8, 6, 17, 20, 22, 24, 32, 11, 36, 38,
+  9, 10, 43, 45, 47, 2, 29, 31,
+  33, 34, 37,
+  13, 15
+};
+
+void initVariant()
+{
+}
+

variants/promicro/variant.h

@@ -0,0 +1,82 @@
+/*
+ * variant.h
+ * Copyright (C) 2023 Seeed K.K.
+ * MIT License
+ */
+
+ #pragma once
+
+ #include "WVariant.h"
+ 
+ ////////////////////////////////////////////////////////////////////////////////
+ // Low frequency clock source 
+
+#define VARIANT_MCK       (64000000ul)
+
+//#define USE_LFXO      // 32.768 kHz crystal oscillator
+#define USE_LFRC    // 32.768 kHz RC oscillator
+
+////////////////////////////////////////////////////////////////////////////////
+// Power
+
+#define PIN_EXT_VCC          (21)
+#define EXT_VCC              (PIN_EXT_VCC)
+
+#define BATTERY_PIN          (17)
+#define ADC_RESOLUTION       12
+
+////////////////////////////////////////////////////////////////////////////////
+// Number of pins
+
+#define PINS_COUNT           (23)
+#define NUM_DIGITAL_PINS     (23)
+#define NUM_ANALOG_INPUTS    (3)
+#define NUM_ANALOG_OUTPUTS   (0)
+
+////////////////////////////////////////////////////////////////////////////////
+// UART pin definition
+
+#define PIN_SERIAL1_TX       (1)
+#define PIN_SERIAL1_RX       (0)
+
+////////////////////////////////////////////////////////////////////////////////
+// I2C pin definition
+
+#define WIRE_INTERFACES_COUNT 2
+
+#define PIN_WIRE_SDA         (6)
+#define PIN_WIRE_SCL         (7)
+#define PIN_WIRE1_SDA        (13)
+#define PIN_WIRE1_SCL        (14)
+
+////////////////////////////////////////////////////////////////////////////////
+// SPI pin definition
+
+#define SPI_INTERFACES_COUNT 2
+
+#define PIN_SPI_SCK          (2)
+#define PIN_SPI_MISO         (3)
+#define PIN_SPI_MOSI         (4)
+
+#define PIN_SPI_NSS          (5)
+
+#define PIN_SPI1_SCK         (18)
+#define PIN_SPI1_MISO        (19)
+#define PIN_SPI1_MOSI        (20)
+
+////////////////////////////////////////////////////////////////////////////////
+// Builtin LEDs
+
+#define PIN_LED              (22)
+#define LED_PIN              PIN_LED
+#define LED_BLUE             PIN_LED
+#define LED_BUILTIN          PIN_LED
+#define LED_STATE_ON         1
+
+////////////////////////////////////////////////////////////////////////////////
+// Builtin buttons
+
+#define PIN_BUTTON1          (6)
+#define BUTTON_PIN           PIN_BUTTON1
+
+