40c9633238
Some checks failed
Build and deploy Docs site to GitHub Pages / github-pages (push) Has been cancelled
PR Build Check / build (Heltec_v3_companion_radio_ble) (push) Has been cancelled
PR Build Check / build (Heltec_v3_repeater) (push) Has been cancelled
PR Build Check / build (Heltec_v3_room_server) (push) Has been cancelled
PR Build Check / build (LilyGo_Tlora_C6_repeater_) (push) Has been cancelled
PR Build Check / build (PicoW_repeater) (push) Has been cancelled
PR Build Check / build (RAK_4631_companion_radio_ble) (push) Has been cancelled
PR Build Check / build (RAK_4631_repeater) (push) Has been cancelled
PR Build Check / build (RAK_4631_room_server) (push) Has been cancelled
PR Build Check / build (wio-e5-mini_repeater) (push) Has been cancelled
- Новый пример examples/beacon_sensor/ на основе companion_radio - Автоматическая отправка flood-объявления каждые 15 минут - ADV_TYPE_CHAT, ретрансляция через mesh-сеть - Поддержка BMP280 по I2C (Wire1, SDA=7, SCL=8) - Новые build-варианты в variants/heltec_t114/platformio.ini: - Heltec_t114_without_display_beacon_sensor_ble - Heltec_t114_without_display_beacon_sensor_usb - Heltec_t114_beacon_sensor_ble (с дисплеем) - Heltec_t114_beacon_sensor_usb (с дисплеем) - Радиопараметры: 868.731 MHz, SF7, BW62.5, CR7, path hash 1 байт Инструкция по прошивке: 1. pio run -e Heltec_t114_without_display_beacon_sensor_ble -t create_uf2 2. Зажми BOOT на T114, подключи USB, появится диск T114 3. Перетащи firmware.uf2 на диск
37 lines
1.2 KiB
C++
37 lines
1.2 KiB
C++
#pragma once
|
|
#include <cstdint> // For uint8_t, uint32_t
|
|
|
|
#define TELEM_MODE_DENY 0
|
|
#define TELEM_MODE_ALLOW_FLAGS 1 // use contact.flags
|
|
#define TELEM_MODE_ALLOW_ALL 2
|
|
|
|
#define ADVERT_LOC_NONE 0
|
|
#define ADVERT_LOC_SHARE 1
|
|
|
|
struct NodePrefs { // persisted to file
|
|
float airtime_factor;
|
|
char node_name[32];
|
|
float freq;
|
|
uint8_t sf;
|
|
uint8_t cr;
|
|
uint8_t multi_acks;
|
|
uint8_t manual_add_contacts;
|
|
float bw;
|
|
int8_t tx_power_dbm;
|
|
uint8_t telemetry_mode_base;
|
|
uint8_t telemetry_mode_loc;
|
|
uint8_t telemetry_mode_env;
|
|
float rx_delay_base;
|
|
uint32_t ble_pin;
|
|
uint8_t advert_loc_policy;
|
|
uint8_t buzzer_quiet;
|
|
uint8_t gps_enabled; // GPS enabled flag (0=disabled, 1=enabled)
|
|
uint32_t gps_interval; // GPS read interval in seconds
|
|
uint8_t autoadd_config; // bitmask for auto-add contacts config
|
|
uint8_t rx_boosted_gain; // SX126x RX boosted gain mode (0=power saving, 1=boosted)
|
|
uint8_t client_repeat;
|
|
uint8_t path_hash_mode; // which path mode to use when sending
|
|
uint8_t autoadd_max_hops; // 0 = no limit, 1 = direct (0 hops), N = up to N-1 hops (max 64)
|
|
char default_scope_name[31];
|
|
uint8_t default_scope_key[16];
|
|
}; |