42f55e12ae
Some checks failed
Build and deploy Docs site to GitHub Pages / github-pages (push) Has been cancelled
PR Build Check / build (Heltec_v3_companion_radio_ble) (push) Has been cancelled
PR Build Check / build (Heltec_v3_repeater) (push) Has been cancelled
PR Build Check / build (Heltec_v3_room_server) (push) Has been cancelled
PR Build Check / build (LilyGo_Tlora_C6_repeater_) (push) Has been cancelled
PR Build Check / build (PicoW_repeater) (push) Has been cancelled
PR Build Check / build (RAK_4631_companion_radio_ble) (push) Has been cancelled
PR Build Check / build (RAK_4631_repeater) (push) Has been cancelled
PR Build Check / build (RAK_4631_room_server) (push) Has been cancelled
PR Build Check / build (wio-e5-mini_repeater) (push) Has been cancelled
- MeshCore-based Simple Sensor firmware - Heltec T114 without display - BME280 sensor support (temp/humidity/pressure) - Radio: 868.856018 MHz, SF7, BW62.5 kHz, CR4/7 - 2-byte path hash - PlatformIO project
59 lines
1.6 KiB
C++
59 lines
1.6 KiB
C++
#include "T114Board.h"
|
|
|
|
#include <Arduino.h>
|
|
#include <Wire.h>
|
|
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Static configuration for power management
|
|
// Values come from variant.h defines
|
|
const PowerMgtConfig power_config = {
|
|
.lpcomp_ain_channel = PWRMGT_LPCOMP_AIN,
|
|
.lpcomp_refsel = PWRMGT_LPCOMP_REFSEL,
|
|
.voltage_bootlock = PWRMGT_VOLTAGE_BOOTLOCK
|
|
};
|
|
|
|
void T114Board::initiateShutdown(uint8_t reason) {
|
|
#if ENV_INCLUDE_GPS == 1
|
|
pinMode(GPS_EN, OUTPUT);
|
|
digitalWrite(GPS_EN, LOW);
|
|
#endif
|
|
digitalWrite(SX126X_POWER_EN, LOW);
|
|
|
|
bool enable_lpcomp = (reason == SHUTDOWN_REASON_LOW_VOLTAGE ||
|
|
reason == SHUTDOWN_REASON_BOOT_PROTECT);
|
|
pinMode(PIN_BAT_CTL, OUTPUT);
|
|
digitalWrite(PIN_BAT_CTL, enable_lpcomp ? HIGH : LOW);
|
|
|
|
if (enable_lpcomp) {
|
|
configureVoltageWake(power_config.lpcomp_ain_channel, power_config.lpcomp_refsel);
|
|
}
|
|
|
|
enterSystemOff(reason);
|
|
}
|
|
#endif // NRF52_POWER_MANAGEMENT
|
|
|
|
void T114Board::begin() {
|
|
NRF52Board::begin();
|
|
|
|
pinMode(PIN_VBAT_READ, INPUT);
|
|
|
|
#if defined(PIN_BOARD_SDA) && defined(PIN_BOARD_SCL)
|
|
Wire.setPins(PIN_BOARD_SDA, PIN_BOARD_SCL);
|
|
#endif
|
|
|
|
Wire.begin();
|
|
|
|
#ifdef P_LORA_TX_LED
|
|
pinMode(P_LORA_TX_LED, OUTPUT);
|
|
digitalWrite(P_LORA_TX_LED, HIGH);
|
|
#endif
|
|
|
|
pinMode(SX126X_POWER_EN, OUTPUT);
|
|
#ifdef NRF52_POWER_MANAGEMENT
|
|
// Boot voltage protection check (may not return if voltage too low)
|
|
// We need to call this after we configure SX126X_POWER_EN as output but before we pull high
|
|
checkBootVoltage(&power_config);
|
|
#endif
|
|
digitalWrite(SX126X_POWER_EN, HIGH);
|
|
delay(10); // give sx1262 some time to power up
|
|
} |