Updated Menu (markdown)
egzumer
166
Menu.md
166
Menu.md
@@ -1,87 +1,91 @@
|
||||
# Main menu
|
||||
* `Step` - step of the frequency, up/down buttons change frequency by this value, also you can only set a frequency that is multiple of this value
|
||||
* `TxPwr` - radio output power
|
||||
* `RxDCS` - receiver Digital-Coded Squelch, if you enable this, squelch will only unlock if this code is being received
|
||||
* `RxCTCS` - receiver Continuous Tone-Coded Squelch System, squelch will only unlock if this code is being received
|
||||
* `TxDCS` - transmitter Digital-Coded Squelch, radio will send given code while transmitting
|
||||
* `TxCTCS` - transmitter Continuous Tone-Coded Squelch System, radio will send given code while transmitting
|
||||
* `TxODir` - transmitter frequency offset direction
|
||||
* `TxOffs` - transmitter frequency offset value
|
||||
* `W/N` - bandwidth used by transceiver
|
||||
* WIDE - 25kHz
|
||||
* NARROW - 12.5kHz
|
||||
* `Scramb` - scrambler, distorts the audio so it would be harder to understand for other listeners, if two radios use the same setting they can communicate
|
||||
* `BusyCL` - busy channel lockout, blocks radio from transmitting while signal is being received
|
||||
* `Compnd` - compander (compressor/expander), allows signals with a large dynamic range to be transmitted over facilities that have a smaller dynamic range capability, improves audio quality, both radios should use this option
|
||||
* `Demodu` - demodulator mode, default is FM, AM can be used for listening only
|
||||
* `ScAdd1` - add channel to scan list 1
|
||||
* `ScAdd2` - add channel to scan list 2
|
||||
* `ChSave` - save current setting to a memory channel
|
||||
* `ChDele` - delete memory channel
|
||||
* `ChName` - modify memory channel name
|
||||
* `SList` - selects which channel is used by memory channel scanner
|
||||
* `SList1` - channels assigned to scan list 1
|
||||
* `SList2` - channels assigned to scan list 2
|
||||
* `ScnRev` - scan resume mode
|
||||
* CARRIER - resume scan after signal disappears
|
||||
* TIMEOUT - resume scan after 5 seconds pause
|
||||
* STOP - after receiving a signal, stop the scan
|
||||
* `F1Shrt` - side button 1 short press function
|
||||
* `F1Long` - side button 1 long press function
|
||||
* `F2Shrt` - side button 2 short press function
|
||||
* `F2Long` - side button 2 long press function
|
||||
* `KeyLck` - auto keypad lock option
|
||||
* `TxTOut` - max transmission time limit
|
||||
* `BatSav` - battery save option, the rate between active time and sleep time
|
||||
* `Mic` - microphone sensitivity
|
||||
* `MicBar` - microphone bar that appears while transmitting
|
||||
* `ChDisp` - channel display style
|
||||
* `POnMsg` - power on message
|
||||
* `BatTxt` - additional battery value on the status bar in % or V
|
||||
* `BackLt` - backlight duration
|
||||
* `BltTRX` - backlight activation on TX or RX
|
||||
* `Beep` - keypad press beep sound
|
||||
* `Roger` - roger beep at the end of transmission
|
||||
* `STE` - squelch tail eliminator, eliminates noise at the end of a transmission
|
||||
* `RP STE` - repeater squelch tail eliminator
|
||||
* `1 Call` - one key call channel, lets you quickly switch to the channel with `9 Call` button
|
||||
* `ANI ID` - DTMF communication radio ID
|
||||
* `UPCode` - DTMF code that is sent at the beginning of transmission
|
||||
* `DWCode` - DTMF code that is sent at the end of a transmission
|
||||
* `PTT ID` - sets if `UPCode` and/or `DWCode` should be transmitted
|
||||
* `D ST` - DTMF side tone switch, lets you hear transmitted tones in the radio speaker
|
||||
* `D Resp` - DTMF decoding response
|
||||
* DO NOTHING: do nothing
|
||||
* RING - Local ringing
|
||||
* REPLY - reply response
|
||||
* BOTH - local ringing + reply response
|
||||
* `D Hold` - DTMF auto reset time
|
||||
* `D Prel` - DTMF pre-load time
|
||||
* `D Decd` - enables DTMF decoder
|
||||
* `D List` - list of DTMF constacts
|
||||
* `D Live` - displays DTMF codes received by radio in the middle of the screen
|
||||
* `AM Fix` - activates autogain AM fix function
|
||||
* `VOX` - voice TX activation sensitivity level
|
||||
* `BatVol` - battery voltage and percentage
|
||||
* `RxMode` - sets how how the upper and lower frequency is used
|
||||
* MAIN ONLY - always transmits and listens on the main frequency
|
||||
* DUAL RX RESPOND - listens to both frequencies, if signal is received on the secondary frequency it locks to it for a couple of seconds so you can respond to the call
|
||||
* CROSS BAND - always transmits on the primary and listens on the secondary frequency
|
||||
* MAIN TX DUAL RX - always transmits on the primary, listens to both
|
||||
* `Sql` - squelch sensitivity level
|
||||
|
||||
1. `Step` - step of the frequency, up/down buttons change frequency by this value, also you can only set a frequency that is multiple of this value
|
||||
1. `TxPwr` - radio output power
|
||||
1. `RxDCS` - receiver Digital-Coded Squelch, if you enable this, squelch will only unlock if this code is being received
|
||||
1. `RxCTCS` - receiver Continuous Tone-Coded Squelch System, squelch will only unlock if this code is being received
|
||||
1. `TxDCS` - transmitter Digital-Coded Squelch, radio will send given code while transmitting
|
||||
1. `TxCTCS` - transmitter Continuous Tone-Coded Squelch System, radio will send given code while transmitting
|
||||
1. `TxODir` - transmitter frequency offset direction
|
||||
1. `TxOffs` - transmitter frequency offset value
|
||||
1. `W/N` - bandwidth used by transceiver
|
||||
* WIDE - 25kHz
|
||||
* NARROW - 12.5kHz
|
||||
1. `Scramb` - scrambler, distorts the audio so it would be harder to understand for other listeners, if two radios use the same setting they can communicate
|
||||
1. `BusyCL` - busy channel lockout, blocks radio from transmitting while signal is being received
|
||||
1. `Compnd` - compander (compressor/expander), allows signals with a large dynamic range to be transmitted over facilities that have a smaller dynamic range capability, improves audio quality, both radios should use this option
|
||||
1. `Demodu` - demodulator mode, default is FM, AM can be used for listening only
|
||||
1. `ScAdd1` - add channel to scan list 1
|
||||
1. `ScAdd2` - add channel to scan list 2
|
||||
1. `ChSave` - save current setting to a memory channel
|
||||
1. `ChDele` - delete memory channel
|
||||
1. `ChName` - modify memory channel name
|
||||
1. `SList` - selects which channel is used by memory channel scanner
|
||||
1. `SList1` - channels assigned to scan list 1
|
||||
1. `SList2` - channels assigned to scan list 2
|
||||
1. `ScnRev` - scan resume mode
|
||||
* CARRIER - resume scan after signal disappears
|
||||
* TIMEOUT - resume scan after 5 seconds pause
|
||||
* STOP - after receiving a signal, stop the scan
|
||||
1. `F1Shrt` - side button 1 short press function
|
||||
1. `F1Long` - side button 1 long press function
|
||||
1. `F2Shrt` - side button 2 short press function
|
||||
1. `F2Long` - side button 2 long press function
|
||||
1. `M Long` - menu button long press function
|
||||
1. `KeyLck` - auto keypad lock option
|
||||
1. `TxTOut` - max transmission time limit
|
||||
1. `BatSav` - battery save option, the rate between active time and sleep time
|
||||
1. `Mic` - microphone sensitivity
|
||||
1. `MicBar` - microphone bar that appears while transmitting
|
||||
1. `ChDisp` - channel display style
|
||||
1. `POnMsg` - power on message
|
||||
1. `BatTxt` - additional battery value on the status bar in % or V
|
||||
1. `BackLt` - backlight duration
|
||||
1. `BLMin` - minimal backlight brightness, when the screen backlight turns OFF it will go dim to this value
|
||||
2. `BLMax` - maximal backlight brightness, when the screen backlight turns ON it will turn bright to this value
|
||||
1. `BltTRX` - backlight activation on TX or RX
|
||||
1. `Beep` - keypad press beep sound
|
||||
1. `Roger` - roger beep at the end of transmission
|
||||
1. `STE` - squelch tail eliminator, eliminates noise at the end of a transmission
|
||||
1. `RP STE` - repeater squelch tail eliminator
|
||||
1. `1 Call` - one key call channel, lets you quickly switch to the channel with `9 Call` button
|
||||
1. `ANI ID` - DTMF communication radio ID
|
||||
1. `UPCode` - DTMF code that is sent at the beginning of transmission
|
||||
1. `DWCode` - DTMF code that is sent at the end of a transmission
|
||||
1. `PTT ID` - sets if `UPCode` and/or `DWCode` should be transmitted
|
||||
1. `D ST` - DTMF side tone switch, lets you hear transmitted tones in the radio speaker
|
||||
1. `D Resp` - DTMF decoding response
|
||||
* DO NOTHING: do nothing
|
||||
* RING - Local ringing
|
||||
* REPLY - reply response
|
||||
* BOTH - local ringing + reply response
|
||||
1. `D Hold` - DTMF auto reset time
|
||||
1. `D Prel` - DTMF pre-load time
|
||||
1. `D Decd` - enables DTMF decoder
|
||||
1. `D List` - list of DTMF constacts
|
||||
1. `D Live` - displays DTMF codes received by radio in the middle of the screen
|
||||
1. `AM Fix` - activates autogain AM fix function
|
||||
1. `VOX` - voice TX activation sensitivity level
|
||||
1. `BatVol` - battery voltage and percentage
|
||||
1. `RxMode` - sets how how the upper and lower frequency is used
|
||||
* MAIN ONLY - always transmits and listens on the main frequency
|
||||
* DUAL RX RESPOND - listens to both frequencies, if signal is received on the secondary frequency it locks to it for a couple of seconds so you can respond to the call
|
||||
* CROSS BAND - always transmits on the primary and listens on the secondary frequency
|
||||
* MAIN TX DUAL RX - always transmits on the primary, listens to both
|
||||
1. `Sql` - squelch sensitivity level
|
||||
|
||||
# Hidden menu
|
||||
|
||||
Hidden menu is accessed by holding `PTT` + `SIDE BUTTON 1` while turning on the radio
|
||||
|
||||
* `F Lock` - sets the frequency band plan for certain area
|
||||
* `Tx 200` - enables TX on 200MHz
|
||||
* `Tx 350` - enables TX on 350MHz
|
||||
* `Tx 500` - enables TX on 500MHz
|
||||
* `350 En` - enables RX on 350MHz
|
||||
* `ScraEn` - enables scrambler function
|
||||
* `TxEnab` - disables TX on all frequencies
|
||||
* `BatCal` - battery calibration, measure the voltage on the back of the radio, and adjust the value in the menu accordingly
|
||||
* `Reset` - resets radio configuration settings
|
||||
* VFO - removes only channel settings
|
||||
* ALL - resets all radio settings
|
||||
61. `F Lock` - sets the frequency band plan for certain area
|
||||
1. `Tx 200` - enables TX on 200MHz
|
||||
1. `Tx 350` - enables TX on 350MHz
|
||||
1. `Tx 500` - enables TX on 500MHz
|
||||
1. `350 En` - enables RX on 350MHz
|
||||
1. `ScraEn` - enables scrambler function
|
||||
1. `TxEnab` - disables TX on all frequencies
|
||||
1. `BatCal` - battery calibration, measure the voltage on the back of the radio, and adjust the value in the menu accordingly
|
||||
1. `Reset` - resets radio configuration settings
|
||||
* VFO - removes only channel settings
|
||||
* ALL - resets all radio settings
|
||||
Reference in New Issue
Block a user